3D MIXER PHARMACEUTICAL FOOD ROTATING DRUM POWDER MIXER
- Introduction
- The 3D-Ribbor Mixer as called Three-dimensional mixing equipment , As a high efficient mixing equipment , this machine is used for highly uniform mixing of powdery and particle materials in such trades as pharmaceutical, food, chemical, light industry, machinery, electronics , mining and metallurgy, national defense industry and scientific research etc.
- Product features
- 1. the volume can be customized, the mixing effect is good, the three-phase movement of the cylinder caused by axial rotation makes the material mixing uniformity reach more than 99.5%, and the mixing time is short
- 2. It can be configured with multiple different volume cylinders to switch and use, especially suitable for small experimental test mixing needs
- 3. three-dimensional axial movement, so that the material in the weightless and mixing rapidly mixed evenly, the internal no need to configure the stirring rod to achieve no secondary mixing pollution of the material
- 4. A variety of closed feeding methods are preferred for feeding, and the caliber can be seamlessly closed
- 5. The discharge method is reasonable and efficient, so as to achieve no residue of the material, and the discharge is more thorough and stable.
- Selection Points:
- Full capacity of the equipment: 50L ~ 1000L
- Mixed volume ratio of equipment: > 60% full load rate
- The mixing time used can be set
- The drive configuration power is 1.5KW-11KW
- Equipment materials can be 316L, 321, 304, carbon steel, and lining
Working principle
Mixing barrel is suspended on ends of driving and driven axles through two Y type universal joints that are
crossing and vertical to each other in the space. When driving axle is driven to rotate, universal joint makes
the barrel perform composite motion including horizontal moving, rotating and turning etc, in the space,
by which, materials also performs 3-dimensional motion inside the barrel. Several kinds of materials inside
the barrel flow, diffuse, penetrate each other and finally form uniform status.
Structure:
The machine is composed of the base, transmission system, electrical control system, multi-directional
motion mechanism, mixing barrel and other components, and the mixing barrel in direct contact with the
material is made of stainless steel material, and the inner and outer walls of the barrel are polished. Fully
compliant with GMP requirements.
Product advantages
● The mixing cylinder of this machine has multi-directional movement, no centrifugal force of the material,
incomparable heavy segregation and delamination, accumulation phenomenon, each component can have
a disparity in weight ratio, high mixing rate, is currently the ideal product in various mixers.
● Large cylinder loading rate, up to 90% (ordinary mixer is only 50%), high efficiency, short mixing time.
● The whole part of the cylinder is an arc transition, which has been precision polished.
● Used in pharmaceutical, chemical, food, light industry, electronics, machinery, mining and metallurgy and
other industries.
● High uniformity mixing of powdered and granular materials in the national defense industry and various
scientific research units.
Technical parameter
Product details
Principle of operation
1. The machine adopts electromagnetic speed regulation (or frequency conversion), before starting, turn
on the total power supply, the power indicator is on, and then start the motor button, and then start the on-off switch on the speed regulation panel (the frequency converter can touch the button), the indicator light is on, and then slowly rotate to achieve the increased mixed speed.
2. After the mixing is over, according to the boot sequence, the reverse shutdown, if the unloading is found to be unsatisfactory, the button can be jogged to meet the unloading requirements.
Attention
1. The mixing of the machine is a three-position space mixing, in the effective operation range of the barrel should be added safety protection bar, so as to avoid the occurrence of life safety accidents, before the start of the cylinder body should not stand, to avoid accidents.
2. When loading and unloading, the jog of the equipment must be stopped to prevent the failure of the electrical appliances and cause necessary accidents.
3. In the process of operation, if abnormal conditions are found in the equipment, it should be stopped immediately for inspection, and the hidden dangers of the accident can be started before it can be started.
4. The contact parts of each transmission of the equipment are regularly added with lubricating oil and grease (three months)
5. The feedback knob and speed control knob of the operation panel shall not be changed arbitrarily, and
it has been proofread before leaving the factory.
Maintenance and Upkeep
1.Preparation for operation:
a. Check whether there is a "good" certificate of equipment.
b. The base is flat and tightens the foot screws to avoid vibration.
c. Regularly refuel the rotating bearings at both ends to avoid jamming and abnormalities.
D. Turn on the power switch, jog test 3-5 turns without abnormality.
2. Maintenance:
a. Pay attention to the lubrication of the bearing housing at both ends.
b. In the event of a malfunction, the cause should be checked after stopping.
c. Frequently check each part. Tighten the body and do not allow loosening.
d. Check the integrity of the equipment and whether the components and accessories are complete.
e, daily maintenance is usually carried out by the operator after work every day, 15-30 minutes before work,
through the inspection, cleaning and wiping of the equipment, so that the equipment is in a neat, clean,
safe and good state.
